![]() Weingartz also sells parts for all outdoor power equipment at. The staff and experts at Weingartz work diligently to provide the best service possible and give honest and helpful advice to each and every customer. Over time, we morphed into the “power equipment superstore” that now defines all of our locations. In the 1970s, we began to focus exclusively on outdoor power equipment. Weingartz, family owned and operated, began in 1945 as a farm supply store for local Michigan families. How to Mix the Correct Ratio of Fuel and Oil Wear a mask or properly fitted respirator to avoid the harmful vapors. ![]() Store this fluid away from heat and only use in a well-ventilated area. Do not use it when your machine’s ignition is on or the engine is running. It is for temporary use until you can bring your machine in for service.Įxercise extreme caution when using starting fluid. Again, use this fluid as a diagnostic tool. Even in 2-cycle applications like your snow blower!ĭo not use starting fluid on your machine over and over again. It’s a colorless, odorless fluid that contains just the right amount of diethyl ether, petroleum gas, and upper cylinder lubricant that can be safely used in all of our equipment. We would recommend “ John Deere’s 80% Premium Ether Starting Fluid”. A recommendation would be substituting starting fluid with a carburetor cleaner since most carburetor cleaner products contain lubricants, but please refer to the contents before use! For the purpose of cold-start in a 2-cycle snow blower, a short burst will suffice. It would be like using ‘straight’ (unmixed) gasoline. Some 2-cycle engines can also be damaged by using starting fluid since most contain no lubricating properties. Using ether spray in this application can lead to engine damage due to its highly flammable properties. It’s generally not recommended for some equipment with diesel engines that use glow-plugs or have a preheating system. Depending on the equipment you’re trying to start, there are some cautionary instances that should be considered before using. A short burst is all that should be necessary for either location. Another location is directly into the spark plug port of the cylinder. After removing the air cleaner, the fluid should be sprayed directly into the intake port. In 4-stroke applications, the easiest location is the intake. If your machine’s engine does not start, and starting fluid helps it start momentarily before quitting, you know that the engine isn’t getting its proper fuel delivery and it’s likely the carburetor may need to be cleaned and/or rebuilt. It can be used as a diagnostic tool as well. Since the engine does not need to be cranked so much, starting fluid has the added benefit of prolonging the life of your battery. It’s especially helpful with equipment that rarely gets used and on cold-starts for snow blowers and even lawn mowers late in the fall season. Its name suggests its use – to assist you in starting a stubborn engine. This method will work best with a mildly flooded engine.Starting fluid is a chemical spray product containing a blend of volatile hydrocarbons, diethyl ether, and carbon dioxide (as a propellant). Maybe go make a cup of hop tea while you wait. Let your chainsaw sit for 15-20 minutes to allow the fuel to evaporate from the engine and then to repeat the starting instructions. Spray the starting fluid for about two seconds, then try to turn the engine over. ![]() Aim the can's nozzle at the air intake from about 12 inches (20 centimeters) away. Spray a small amount of starting fluid into the air intake. This can help ensure the fuel ignites when the ignition key is turned – getting your vehicle started and back on the road.Īlso Know, how do you use an engine starter spray? How does Quick Start spray work? Bradex Easy Start helps engines start by increasing the combustibility of the fuel and the air mixture within the engine. Starting fluid is sprayed into the engine intake near the air filter, or into the carburetor bore or a spark plug hole of an engine to get added fuel to the combustion cylinder quickly. If its totally bone dry wait maybe 20 seconds and it should be aok.Īlso question is, where do I spray starter fluid? Re: Starting fluid Next time you have a dry tank, only fill it about half way to begin with then shake the saw up and down a couple of times and the pressure from the expanding fuel will fill the line.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |